Sensors and Accessories

6.4 Super Duty Exhaust Gas Temperature Sensor

SKU : 2465

EGT sensors are required on previously deleted trucks in order to utilize DCS 5R110 tuning service. 08-10 Super Duty trucks require 3 sensors. Replacement for Ford part #8C3Z-5J213-D.

Ambient Air Temperature Sensor- 03-05 Cummins

SKU : 1034

The Dodge ambient air temperature sensor is necessary for the '03-'05 Cummins engines. This is located in the air intake tube on the Dodge truck.

Billet Aluminum Cummins 12 Valve Crank Sensor Mounting Bracket

SKU : 1194

This Billet Aluminum Bracket is designed to hold a stock Cummins 12 Valve Crank Sensor. Mounts on timing cover where a stock bracket would have been.  This bracket is necessary in 12 valve conversions in which a tach signal is needed and a stock...

Crankshaft Sensor bracket - 6.0 Ford using Common rail

SKU : 1939

This bracket allows you to use your existing Ford crankshaft sensor which reads the Cummins tone ring. Used on 2003-2007 Ford 6.0 Super Duty to Cummins Common Rail conversions.

Cruise Helper

SKU : 2461

Want cruise control in your 2005 to 2010 swap truck, but don't want to modify your steering wheel buttons? The solution is here! The SwapHelper.com Cruise Helper allows you to use a cruise servo (typically from a gasoline powered Ford) in your swap...

Cummins Crankshaft Position Sensor Pigtail 97-98

SKU : 2467

Replacement pigtail for Cummins Crank Shaft Sensor. Commonly used on 1997-1998 12 valve engines and DCS 12 valve harnesses.

Cummins Crankshaft Position Sensor- 1997-1998 Dodge (Square Connector)

SKU : 2460

Dodge Cummins Crankshaft Position Sensor for 1997/1998 12-Valve engines. Please note this is the Square Connector. Replacement Cummins part #3923129, manufactured by Sook Sensors. If you need a crank sensor mounting bracket, see SKU 1194

DCS Pedal Module, 2003-2006 Dodge Cummins 5.9L in 2003-2010 Ford Super Duty

SKU : 2649

Stand-Alone DCS Throttle Pedal Module, 2003-2006 Cummins in 2003-2010 Ford Super Duty The Stand-Alone DCS Throttle Pedal Module is available to customers choosing to not utilize DCS conversion wiring service. The module can be used in 2003-2010 Ford...

DCS Throttle Pedal Module, 2007-2009 Cummins in 2003-2010 Ford Super Duty -

SKU : 2648

Stand-Alone DCS Throttle Pedal Module, 2007-2009 Cummins in 2003-2010 Ford Super Duty The Stand-Alone DCS Throttle Pedal Module is available to customers choosing to not utilize DCS conversion wiring service. The module can be used in 2003-2010 Ford...

Dodge Cummins Crankshaft Position Sensor- '89 - '97 Dodge (Round Connector)

SKU : 2340

Dodge Cummins Crankshaft Position Sensor for '89 - '97 12 Valve engines. Please note this is the Round Connector. Manufactured by Sook Sensors.

Intake Grid Heater Control Module

SKU : 3123

This controller and related circuitry will operate as a stand-alone engine grid heater controller for all, two grid, air intake heater systems. Features: Preheat grid heater cycle time is determined by IAT (Intake Air Temperature). Preheat will...

P-Pump Fuel Shutdown Solenoid Connector: Harness Side

SKU : 2074

No need to hard-wire your shutdown solenoid when you install this pigtail. Main power has an in-line fuse, secondary power requires a "key-on" power supply, and a ground; it's that simple!