Parts

Billet Aluminum Cummins 12 Valve Crank Sensor Mounting Bracket

SKU : 1194

This Billet Aluminum Bracket is designed to hold a stock Cummins 12 Valve Crank Sensor. Mounts on timing cover where a stock bracket would have been.  This bracket is necessary in 12 valve conversions in which a tach signal is needed and a stock...

Billet High Flow Intake Manifold / Plenum Plate 12V Cummins

SKU : 2662

Designed to fit with intercooled and non-intercooled engines Fit Cummins 12 valve diesel engines Plate only. Re-uses factory hardware.

Billet High Flow Intake Manifold / Plenum Plate 4BT Cummins

SKU : 3126

Fit Cummins 4BT diesel engines Plate only. Re-uses factory hardware.

Clutch Kit 03-10 Ford 6.0L & 6.4L -6 Speed to Cummins, Street Dual Disc (650 hp, 1300 ft/lbs) (SKU 2145)

SKU : 2145

This South Bend Clutch Kit is for Cummins conversions using the 03-10 Ford 6.0L & 6.4L diesel ZF-6 speed. The kit includes a custom Dodge Cummins 6 speed flywheel, clutch, Ford release bearing, sealed ball bearing pilot bearing, and a clutch...

Clutch Kit 87-97 Ford ZF-5 Speed to Cummins, High Performance Dual Disc (650 hp, 1300 ft/lbs)(SKU 2143)

SKU : 2143

This South Bend Clutch Kit is for Cummins conversions using the 87-97 Ford 7.3L diesel ZF-5 speed. The kit includes a custom Dodge Cummins 5 speed flywheel, clutch, Ford release bearing, sealed ball bearing pilot bearing, and a clutch alignment tool (all...

Clutch Kit 99-03 Ford 7.3-6 Speed to Cummins, High Performance Dual Disc (650 hp, 1300 ft/lbs) (SKU 2144)

SKU : 2144

This South Bend Clutch Kit is for Cummins conversions using the 99-03 Ford 7.3L diesel ZF-6 speed. The kit includes a custom Dodge Cummins 6 speed flywheel, clutch, Ford release bearing, sealed ball bearing pilot bearing, and a clutch alignment tool (all...

Common Rail Cummins Power Steering Pump Pulley

SKU : 1993

Replacement pulley for bent or missing power steering pump pulleys on 2003-2007 5.9L Common Rail power steering pumps that have a snap ring backing plate. The 8-rib billet aluminum pulley is stronger than plastic pulleys, and it looks a lot better too. ...

Complete A/C Line: 1999-2007 Super Duty 250-550 - 5.4, 6.8, 7.3, 6.0 Except Excursions to 1994-2005 Dodge A/C compressor

SKU : 2178

DCS offers a premade A/C line. Simply bolt the lines to the Dodge A/C compressor, re-attach the lines to the Ford drier and condenser, recharge the system and you’ll be up and running. It’s that simple! You must be using the DCS engine mounts in the rear...

Conversion Friendly Engine Harness for Cummins 12 Valve Engine 1994-1998

SKU : 2613

This harness is designed to make your 1994-1998 Cummins 12 valve engine start and run in any chassis by simply connecting 12V power and ground. The harness comes pre-wired for the following: Swap Helper Tach Adapter Grid Heater Control Module Dodge...

Conversion Friendly, DPS Swap 12V Exhaust Manifold, 2-Piece. DPS-RV-12V-Manifold. (SKU 2147)

SKU : 2147

This exhaust manifold moves the turbo away from the A/C box on the fire wall and provides about 6" of clearance, with additional hood clearance as well. The turbocharger must be re-oriented so that the oil drain tube points straight down. Stock manifolds...

Crankshaft Sensor bracket - 6.0 Ford using Common rail

SKU : 1939

This bracket allows you to use your existing Ford crankshaft sensor which reads the Cummins tone ring. Used on 2003-2007 Ford 6.0 Super Duty to Cummins Common Rail conversions.

Cruise Helper

SKU : 2461

Want cruise control in your 2005 to 2010 swap truck, but don't want to modify your steering wheel buttons? The solution is here! The SwapHelper.com Cruise Helper allows you to use a cruise servo (typically from a gasoline powered Ford) in your swap...